Try 100% Updated 350-501 Exam Questions [2023]
Pass 350-501 Exam - Real Questions and Answers
NEW QUESTION # 197
Refer to the exhibit:
A network administrator wants to enhance the security for SNMP for this configuration.
Which action can the network administrator implement?
- A. Add a community string to the existing entry
- B. Maintain the configuration but switch to an encrypted password for device access through SSH
- C. Re-configure to use SNMPv3.
- D. Re-configure to use SNMPv2 with MD5 authentication
Answer: C
NEW QUESTION # 198
Refer to the exhibit:
P3 and PE4 are at the edge of the service provider core and serve as ABR routers Aggregation areas are on either side of the core.
Which statement about the architecture is true?
- A. To support seamless MPLS. TDP must be used as the label protocol
- B. To support seamless MPLS, the BGP route reflector feature must be disabled
- C. If each area is running its own IGP. BGP must provide an end-to-end MPLS LSP
- D. If each area is running its own IGP. the ABR routers must redistribute the IGP routing table into BGP
Answer: C
NEW QUESTION # 199 
Refer to the exhibit. Which three outcomes occur if the prefix list is added to the neighbor? (Choose three.)
- A. 192.168.0.0/16 is denied.
- B. 192.168.0.0/19 is denied.
- C. 192.168.0.0/16 is permitted.
- D. 192.168.0.0/19 is permitted
- E. 192.168.0.0/17 is permitted
- F. 192.168.0.0/17 is denied.
Answer: A,D,F
Explanation:
Section: Architecture
NEW QUESTION # 200
Refer to the exhibit.
An engineer is configuring an administrative domain in the given multi-vendor environment with PIM-SM. Which feature must the engineer implement so that devices will dynamically learn the RP?
- A. Auto-RP
- B. BIDIR-PIM
- C. BSR
- D. SSM
Answer: A
NEW QUESTION # 201
You are writing an RPL scnpt to accept routes only from certain autonomous systems Consider this code.
If you apply this code to BGP filters, which effect does the code have on your router?
- A. denies routes from AS 7007
- B. denies routes from AS 7070
- C. allows routes from AS 7077
- D. allows routes from AS 770
Answer: C
NEW QUESTION # 202
Refer to the exhibit:
Which effect of this configuration is true?
- A. The two routers fail to form a neighbor relationship because they have different ISIS area types.
- B. The two routers fail to form a neighbor relationship because the authentication configuration is missing
- C. The two routers fail to form a neighbor relationship because their system IDs are different.
- D. The two routers successfully form a neighbor relationship
Answer: D
NEW QUESTION # 203
Refer to the exhibit. What reestablishes the OSPF neighbor relationship between Router 1 and Router 2?
- A. OSPF process IDs match
- B. authentication is added to the configuration
- C. hello intervals match
- D. correct wildcard mask is used on Router 2
Answer: C
NEW QUESTION # 204
Refer to the exhibit:
This output is included at the end of an output that was provided by a device using NETCONF.
What does the code show?
- A. It shows that the running configuration is blank
- B. It shows NETCONF uses remote procedure calls.
- C. It shows the hostname of the device as rpc-reply
- D. It shows that the full configuration is being modeled by VANG
Answer: B
NEW QUESTION # 205
Drag and drop the functionalities from the left onto the correct target fields on the right.
Answer:
Explanation:
NEW QUESTION # 206
Refer to the exhibit:
Which three outcomes occur if the prefix list is added to the neighbor? (Choose three)
- A. 192.168 0.0/17 is permitted
- B. 192.168.0.0/16 is denied
- C. 192.168 0.0/19 is denied.
- D. 192.168 0.0/17 is denied.
- E. 192.168 0.0/16 is permitted
- F. 192.168 0.0/19 is permitted
Answer: A,B,F
NEW QUESTION # 207
Refer to the exhibit:
This output is included at the end of an output that was provided by a device using NETCONF.
What does the code show?
- A. It shows that the running configuration is blank
- B. It shows NETCONF uses remote procedure calls.
- C. It shows the hostname of the device as rpc-reply
- D. It shows that the full configuration is being modeled by VANG
Answer: B
NEW QUESTION # 208
Drag and Drop Question
Drag and drop the descriptions from the left onto the corresponding OS types on the right.
Answer:
Explanation:
NEW QUESTION # 209
Refer to the exhibit. An engineer configured R6 as the headend LSR of an RSVP-TE LSP to router XR2, with the dynamic path signaled as R6-R2-R5-XR2. and set the OSPF cost of all links to 1. MPLS autotunnel backup Is enabled on all routers to protect the LSP.
Which two NNHOP backup tunnels should the engineer use to complete the implementation?
(Choose two.)
- A. The R6 backup tunnel path R6-R1-R2.
- B. The R2 backup tunnel path R2-R1-R4-XR1-XR2.
- C. The R6 backup tunnel path R6-R1-R4-R5.
- D. The R2 backup tunnel path R2-R5 across the alternate link.
- E. The R6 backup tunnel path R6-R2-R5
Answer: B,C
NEW QUESTION # 210
Refer to the exhibit:
What is significant about the number 2 in the configuration?
- A. It is the numeric name of the ACL that contains the list of SNMP managers with access to the agent
- B. It represents the version of SNMP running
- C. It indicates two SNMP managers can read and write with the agent using community string cisco test
- D. It dictates the number of sessions that can be open with the SNMP manager
Answer: A
NEW QUESTION # 211
Refer to the exhibit:
A network operator working for service provider with an employee id 3715 15:021 applied this configuration to a router.
Which additional step should the engineer use to enable LDP?
- A. Disable Cisco Express Forwarding globally
- B. Configure the both keyword to enable LDP globally
- C. Delete the static router ID
- D. Enable MPLS LDP on the interface
Answer: D
NEW QUESTION # 212
Which configuration modifies Local Packet Transport Services hardware policies?
A)
B)
C)
D)
- A. Option D
- B. Option A
- C. Option C
- D. Option B
Answer: C
NEW QUESTION # 213
Refer to the exhibit:
Which statement about this configuration is true"?
- A. It requires OSPF to also be running to have optimized Cisco MPLS TE tunnels
- B. It is the configuration for the head-end router of a Cisco MPLS TE tunnel with segment routing
- C. It requires a dynamic Cisco MPLS TE path to be configured for the tunnel to run
- D. It requires an explicit Cisco MPLS TE path to be configured for the tunnel to run
Answer: B
NEW QUESTION # 214 
Refer to the exhibit. A network operator recently configured BGP FlowSpec for the internal IT network. What will be inferred from the configuration deployed on the network?
- A. The policy is learned via BGP FlowSpec and has active traffic
- B. The policy is configured locally on CSR1 and drops all traffic for TCP ports 80 and 443
- C. The policy is learned via BGP FlowSpec and drops all traffic for TCP ports 80 and 443
- D. The policy is configured locally on CSR1 and currently has no active traffic
Answer: B
Explanation:
Section: Architecture
NEW QUESTION # 215
A network operator needs to implement PIM-SSM multicast configuration on customer's network so that users in different domains are able to access and stream live traffic. Which two actions must the engineer perform on the network to make the streaming work? (Choose two.)
- A. Enable IGMP version 3 at the interlace level.
- B. Enable IGMP version 2 at the interface level.
- C. Enable PIM dense mode on the device.
- D. Configure at least one MSDP peer on the network.
- E. Enable PIH sparse mode on the device.
Answer: A,D
NEW QUESTION # 216
What causes multicast traffic to permanently stay on the shared tree and not switch to the source tree?
- A. The SPT threshold is set to infinity.
- B. The RP IP address is configured incorrectly.
- C. The RP announcements are being filtered.
- D. SSM range is being used.
Answer: C
Explanation:
https://www.cisco.com/c/en/us/td/docs/ios/solutions_docs/ip_multicast/White_papers/mcst_ovr.html
NEW QUESTION # 217
Refer to the exhibit:
Which purpose of implementing NSF with this configuration is true?
- A. The router uses NSF to load balance traffic on a routed EtherChannel
- B. The router uses NSF to load balance traffic between two links, with the primary link alternating every
90 seconds - C. The router uses NSF to handle RP switchover while allowing neighbor relationships to remain up
- D. The router uses NSF to reduce neighbor-relationship downtime during RP switchover
Answer: C
NEW QUESTION # 218
Which feature will an operator use while implementing MPLS TE on customer's network, to prevent an LSP from using any overseas inks?
- A. explicit path
- B. bandwidth
- C. SLRG
- D. affinity
Answer: A
NEW QUESTION # 219
......
350-501 Exam Questions Get Updated [2023] with Correct Answers: https://www.examtorrent.com/350-501-valid-vce-dumps.html
Free Cisco 350-501 Test Practice Test Questions Exam Dumps: https://drive.google.com/open?id=17lDgmNr58-HhXQ7_tTqNSLaOGeY0y7sO
