[Feb-2024] CIP Level 2 NACE-CIP2-001 Exam Practice Dumps
2024 NACE-CIP2-001 Premium Files Test pdf - Free Dumps Collection
The Coating Inspector Level 2 exam covers a wide range of topics related to surface preparation, coating application, and inspection techniques. Candidates will be tested on their understanding of coating materials, application methods, and the different types of coatings used in various industries. NACE-CIP2-001 exam will also assess candidates' knowledge of industry standards and regulations related to coatings and corrosion prevention.
NACE-CIP2-001 Exam is an essential certification program for individuals seeking a career in the field of corrosion control and coatings. NACE-CIP2-001 exam is designed to test candidates on their knowledge of coating inspection techniques and industry standards, and passing the exam is a testament to the candidate's expertise and commitment to their profession. The Coating Inspector Level 2 certification is highly regarded in the industry and can open up new career opportunities for individuals seeking to advance their careers in this field.
NEW QUESTION # 28
Which concrete smoothing technique involves scrubbing a mixture of cement mortar over the concrete surface using ai cement sack, gunny sack, or sponge rubber float?
- A. Stoning
- B. Sacking
- C. Acid etching
- D. High-pressure water washing
Answer: B
NEW QUESTION # 29
The cost of qualified Coating Inspection is normally offset by:
- A. Lower Application Costs
- B. Lower Safety Enforcement Costs
- C. Lower Supervision Costs
- D. Lower Coating Life Cycle Costs
Answer: D
NEW QUESTION # 30
On pipelines, which coating is identifiable by its distinct colors, usually light blue, green, or grey?
- A. Liquid epoxies
- B. Concrete
- C. Coal Tar Enamel
- D. Heat-shrink sleeves
Answer: A
NEW QUESTION # 31
When a coating is expected to be exposed to temperatures above 93C (200 F) the best choice would be:
- A. Polyurea
- B. Inorganic Coatings
- C. Organic coatings
- D. Latex
Answer: B
NEW QUESTION # 32
Inspection and Test Plans are provided to:
- A. So the Inspector doesn't have to read the entire specification
- B. Outline the inspection steps, sequencing and pass/fail criteria
- C. So the contractor has a single document to reference
- D. To supersede the requirements of the product data sheets
Answer: B
NEW QUESTION # 33
Because a NACE Level 2 Inspector has been trained in specific destructive tests, it is up to the Inspector to decide if and when a destructive test is required.
- A. False
- B. True
Answer: A
NEW QUESTION # 34
The most likely area of failure on a buried external pipeline coating is the:
- A. Mainline coating
- B. Ground bed
- C. Field joint coating
- D. Areas exposed to Ultra Violet light
Answer: C
NEW QUESTION # 35
As a NACE Level 2 Inspector, NACE clearly indicates that you ate qualified to independently produce final documentation for a shop project.
- A. False
- B. True
Answer: B
NEW QUESTION # 36
Steel shot grit contaminated with oil or grease used in a cetrifugal blast cleaning should be
- A. disposed of properly.
- B. mixed with uncontaminated abrasive
- C. run through the air wash separator.
- D. washed with clean potable water prior to Use.
Answer: A
NEW QUESTION # 37
When measuring the Dry Film Thickness Of liquid coatings applied to galvanized ferrous substrates the most commonly used instrument is the:
- A. Eddy Current Gauge
- B. Magnetic Gauge
- C. Ultra Sonic DFT Gauge
- D. Tooke Gauge
Answer: D
NEW QUESTION # 38
You are working as the only in-house NACE Level 2 Inspector in a shop setting when an independent 3 rd party NACE Level 3 Inspector, representing the owner, presents you with a copy of a Non Conformance Report (NCR) he has written for a NACE2/SSPC SP 10 centrifugal blast which you had previously approved.
Your FIRST preferred course of action is to:
- A. Verbally challenge the NCR
- B. Review the NCR with the other Inspector
- C. Request a re-blast of the item in question
- D. Consult your supervisor
Answer: D
NEW QUESTION # 39
Application of Thermal Spray Coatings requires:
- A. Specialized skills supported by training and experience
- B. The same skills as liquid coatings
- C. No particular skills
- D. The same skills as welding
Answer: A
NEW QUESTION # 40
In the event of a conflict between the Product Data Sheet and the Specification:
- A. The Specification prevails
- B. It is up to the Applicator to decide which one to follow
- C. It is up to the Inspector to decide which one to follow
- D. The Product Data Sheet prevails
Answer: A
NEW QUESTION # 41
When working with someone who is very concerned about Stability and maintaining adherence to the status-quo, the Inspector should try to:
- A. Challenge their value to the team and try to get them out of their comfort zone
- B. Make sure they are the center of attention in all site meetings
- C. Implement immediate to get them motivated
- D. Give them as much advance notice as possible about upcoming changes
Answer: D
NEW QUESTION # 42
In powder coatings, when the particles of powder begin to flow but are not fully liquid, they are in what stage?
- A. Cure stage
- B. Gel stage
- C. Wetting stage
- D. Flow stage
Answer: D
NEW QUESTION # 43
You are the NACE Level 2 inspector reviewing the documentation from a NACE Level 1 you notice significant documentation errors.
Your FIRST preferred course of action is to:
- A. Correct the errors yourself and suggest the Level 1 inspector be replaced
- B. Correct the errors yourself and submit the reports without any further action
- C. Correct the errors yourself and advise your supervisor that the Level 1 Inspector is incompetent
- D. Have the Level 1 Inspector correct the errors and set up remedial training to improve the quality of documentation
Answer: D
NEW QUESTION # 44
The coating applicator has ignored a enface preparation hold point and applied coating over the surface without a sign off from you as the inspector.
Your FIRST preferred course of action is to:
- A. Ignore the situation
- B. Advise the Owner and write a Non-Conformance report
- C. Stop the job
- D. Require the Applicator to remove the coating
Answer: D
NEW QUESTION # 45
Measuring methyl ethyl ketone (MEK) resistance of ethyl silicate inorganic zinc-rich primers by solvent rub requires
- A. 25 single rubs with a saturated cloth.
- B. 50 double rubs with a saturated cloth.
- C. 25 double rubs with a saturated cloth.
- D. 35 single rubs with a saturated cloth.
Answer: B
NEW QUESTION # 46
Surface preparation methods for Non-ferrous metals are:
- A. The same for all Non-FetT0us metals
- B. The same as for Ferrous metals
- C. Specific for each type of Non-ferrous metal
- D. Not required
Answer: C
NEW QUESTION # 47
......
NACE-CIP2-001 Exam is recognized as a standard for coating inspection certification in many industries, including oil and gas, petrochemical, marine, and construction. Coating Inspector Level 2 certification is highly respected and is often used as a requirement for employment in the coating industry. Achieving this certification demonstrates a high level of expertise and commitment to the industry, making it a valuable asset for professionals in this field.
Get ready to pass the NACE-CIP2-001 Exam right now using our CIP Level 2 Exam Package: https://www.examtorrent.com/NACE-CIP2-001-valid-vce-dumps.html
A fully updated 2024 NACE-CIP2-001 Exam Dumps exam guide from training expert ExamTorrent: https://drive.google.com/open?id=1DTrQil7RK_LkuPpmypImB1C7C1V7Be8J
