NACE-CIP2-001 Exam Questions - Real & Updated Questions PDF
Pass Guaranteed Quiz 2022 Realistic Verified Free NACE
NEW QUESTION 57
You are NACE Level 2 Inspector working on a tank lining job where a mobile centrifugal blast unit is being used to blast the tank floor to a NACE No.1/SSPC SP 5. The Contractor has completed his final blast and has called for a hold point inspection. This is the 1 st time you have seen field based centrifugal blast cleaning. You observe what appears to be staining on the substrate however the Contractor assures you this is normal when using centrifugal blast units and what you are seeing is what is defined in the standard as an acceptable variation in appearance.
Your FIRST preferred course of action is to:
- A. Request that the Contractor re-blast the floor
- B. Shut the job down
- C. Call your supervisor
- D. Review the standard with the Contractor and re-inspect the floor
Answer: D
NEW QUESTION 58
You can use magnifiers to examine all of the following EXCEPT
- A. Surface profile
- B. Blisters
- C. Surface cleanliness
- D. Mill scale
Answer: C
NEW QUESTION 59
Non-Conformance Reports are designed to:
- A. Elevate the status of the Inspector
- B. To identify items that do not meet the specification requirements
- C. Punish the Contractor for substandard work
- D. Assist the Owner in negotiating credits from the Contractor
Answer: B
NEW QUESTION 60
Which product, when closely inspected has a green or red layer of fusion bonded epoxy (FBE) that is visible directly on the steel?
- A. Coal Tar Enamel
- B. 2-Layer Polyethylene (PE)
- C. Fusion Bonded Epoxy
- D. 3-Layer Polyethylene (PE)
Answer: D
NEW QUESTION 61
When environmental enclosures are being used an inspector needs to be concerned about:
- A. a), b), and c)
- B. Lighting
- C. Air changes
- D. Structural integrity
Answer: A
NEW QUESTION 62
Which concrete smoothing technique involves scrubbing a mixture of cement mortar over the concrete surface using ai cement sack, gunny sack, or sponge rubber float?
- A. Sacking
- B. High-pressure water washing
- C. Stoning
- D. Acid etching
Answer: A
NEW QUESTION 63
Which standards are generally established by private-sector bodies and are available for use by any person or Organization, private or government?
- A. Mandatory
- B. Consensus
- C. Voluntary
- D. De facto
Answer: C
NEW QUESTION 64
WJ-1 is always performed using UHWJ at pressures above 210 MPa (30,000 PSI)
- A. False
- B. True
Answer: B
NEW QUESTION 65
When performing testing in accordance with ASTM D 2583 the inspector may observe:
- A. Cohesion failure
- B. Cold flow or creep
- C. Adhesion failure
- D. Glue failure
Answer: B
NEW QUESTION 66
Steel shot grit contaminated with oil or grease used in a cetrifugal blast cleaning should be
- A. run through the air wash separator.
- B. disposed of properly.
- C. washed with clean potable water prior to Use.
- D. mixed with uncontaminated abrasive
Answer: B
NEW QUESTION 67
The Concrete Repair Institute's comparators can be used to assess:
- A. Compressive and tensile strength prior to coating
- B. Surface profile prior to coating
- C. Surface cleanliness prior to coating
- D. Contamination levels prior to coating
Answer: B
NEW QUESTION 68
When observing design defects the NACE Inspector should:
- A. Ignore the defect as the inspector can't change the design
- B. Stop the job immediately
- C. Request that the item be rebuilt with a better design for coating
- D. Document the defect and the potential problems that could result
Answer: D
NEW QUESTION 69
Inspection and Test Plans are provided to:
- A. So the contractor has a single document to reference
- B. To supersede the requirements of the product data sheets
- C. So the Inspector doesn't have to read the entire specification
- D. Outline the inspection steps, sequencing and pass/fail criteria
Answer: D
NEW QUESTION 70
Galvanizing performs best in which of the following exposures:
- A. pH below 4
- B. pH of 13
- C. pH above 12
- D. pH between 5-10
Answer: D
NEW QUESTION 71
The solvent sensitivity/solvent wipe test (ASTM D4752) is used to determine the cure of
- A. inorganic zincs.
- B. urethanes.
- C. epoxies.
- D. powder coatings.
Answer: A
NEW QUESTION 72
You are the NACE Level 2 Inspector with the final responsibility to prepare the final report for a very large structural steel shop project which has gone very well. It is due next week. The work has been ongoing for two years and several NACE Level 1 Inspectors have worked under your supervision throughout the project. You find you are missing one week of daily reports for the night shift from the very beginning of the project and despite your best efforts they are cannot found.
You FIRST preferred course of action is to:
- A. Do not complete your report until they can be found
- B. Re-create the reports as not much was going on during night shift anyway
- C. Use creative writing to cover over the fact they are missing
- D. Plainly state in your report that they are missing
Answer: D
NEW QUESTION 73
NACE/SSPC Water Jetting standards are directly equivalent to ISO Abrasive Blast Standards:
- A. False
- B. True
Answer: A
NEW QUESTION 74
A reinforced coating is
- A. less resistant to movement, abrasion, and impact than a non-reinforced coating.
- B. equally resistant to abrasion and impact as a non-reinforced coating.
- C. equally resistant to movement and impact as a non-reinforced coating.
- D. more resistant to movement, abrasion, and impact than a non-reinforced coating.
Answer: D
NEW QUESTION 75
When performing a hardness test on a coating which has elastic properties the inspector is likely to likely to observe:
- A. A very low reading
- B. Cold flow or creep
- C. No difference from any other coating
- D. A very high reading
Answer: B
NEW QUESTION 76
External coatings applied to buried pipelines are generally tested for:
- A. Solvent resistance
- B. Chalking resistance
- C. Gloss level
- D. Cathodic disbondment
Answer: D
NEW QUESTION 77
......
Get to the Top with NACE-CIP2-001 Practice Exam Questions: https://www.examtorrent.com/NACE-CIP2-001-valid-vce-dumps.html
Free CIP Level 2 NACE-CIP2-001 Ultimate Study Guide: https://drive.google.com/open?id=1DTrQil7RK_LkuPpmypImB1C7C1V7Be8J
