2023 100% Free 200-301 Daily Practice Exam With 875 Questions
200-301 exam torrent Cisco study guide
The Cisco 200-301 certification exam is a single exam that replaces the previous CCNA exams. The new exam includes updated content and technologies to reflect the evolving landscape of networking. The exam has a duration of 120 minutes, and consists of 100-120 questions. The exam can be taken at any Pearson VUE testing center, and candidates can schedule their exam online.
Introduction
The primary responsibility of the Associate Network Engineer is to update the technical standards and strategic technical roadmaps. The professionals must take care of the network engineering policies, and operations that include network programmability. The Network Engineer has to act as backup for the LAN/WAN and Firewall teams whenever required. They must install, monitor, and maintain the LAN infrastructure. The professional should make sure smooth and proper functionality of the network system.
The Associate Network Engineer takes care of the hardware components and others such as cabling and wiring. The professionals provide the necessary technical assistance needed for installation and maintenance of WAN infrastructure. They examine and network capacity and implement network tools. The Network Engineer recognizes and resolves network hardware and software problems. They set up user accounts and passwords, and protect access to confidential data.
The Cisco 200-301 exam is the sole requirement for obtaining the Cisco Certified Network Associate (CCNA) certification. This certification is designed to validate a candidate's understanding and knowledge of fundamental networking concepts, technologies, and best practices. The exam is designed to test a candidate's abilities in areas such as network security, automation and programmability, network access, IP connectivity, and network fundamentals.
NEW QUESTION # 399
The SW1 interface g0/1 is in the down/down state. Which two configurations are valid reasons for the interface conditions?(choose two)
- A. The interface is error-disabled
- B. There is a protocol mismatch
- C. The interface is shut down
- D. There is a duplex mismatch
- E. There is a speed mismatch
Answer: A,E
NEW QUESTION # 400
DRAG DROP
Drag and drop the characteristics of networking from the left onto the correct networking types on the right.
Answer:
Explanation:
NEW QUESTION # 401
Drag and drop to the characteristics of networking from the left onto the correct networking types on the right.
Answer:
Explanation:
NEW QUESTION # 402
Connectivity between three routers has been established, and IP services must be configured jn the order presented to complete the implementation Tasks assigned include configuration of NAT, NTP, DHCP, and SSH services.
1. All traffic sent from R3 to the R1 Loopback address must be configured for NAT on R2. All source addresses must be translated from R3 to the IP address of Ethernet0/0 on R2, while using only a standard access list named NAT To verify, a ping must be successful to the R1 Loopback address sourced from R3. Do not use NVI NAT configuration.
2. Configure R1 as an NTP server and R2 as a client, not as a peer, using the IP address of the R1 Ethernet0/2 interface. Set the clock on the NTP server for midnight on January 1, 2019.
3. Configure R1 as a DHCP server for the network 10.1.3.0/24 in a pool named TEST. Using a single command, exclude addresses 1-10 from the range. Interface Ethernet0/2 on R3 must be issued the IP address of 10.1.3.11 via DHCP.
4. Configure SSH connectivity from R1 to R3, while excluding access via other remote connection protocols. Access for user root and password Cisco must be set on router R3 using RSA and 1024 bits. Verify connectivity using an SSH session from router R1 using a destination address of 10.1.3.11. Do NOT modify console access or line numbers to accomplish this task.
Answer:
Explanation:
conf t
R1(config)#ntp master 1
R2(config)#ntp server 10.1.2.1
Exit
Router#clock set 00:00:00 jan 1 2019
ip dhcp pool TEST
network 10.1.3.0 255.255.255.0
ip dhcp exluded-address 10.1.3.1 10.1.3.10
R3(config)#int e0/3
R3(config)#int e0/2
ip address dhcp
no shut
crypto key generate RSA
1024
Copy run start
NEW QUESTION # 403
Refer to the exhibit.
Site A was recently connected to site B over a new single-mode fiber path. Users at site A report Intermittent connectivity Issues with applications hosted at site B.
What is the reason for the problem?
- A. Heavy usage is causing high latency.
- B. An incorrect type of transceiver has been inserted into a device on the link.
- C. The wrong cable type was used to make the connection.
- D. physical network errors are being transmitted between the two sites.
Answer: D
NEW QUESTION # 404
Which two tasks can help you gather relevant facts when you troubleshoot a network problem?
(Choose two)
- A. Ask questions of the users who are affected by the problem
- B. Change one setting or component and then analyze the result
- C. Define the problem in terms of symptoms and causes
- D. Eliminate known issues first
- E. Collect technical data from network management systems and logging servers
Answer: C,E
NEW QUESTION # 405
If you configure syslog messages without specifying the logging trap level, which log messages will the router send?
- A. error conditions only
- B. informational messages only
- C. normal but significant conditions only
- D. all levels except debugging
- E. warning and error conditions only
Answer: D
NEW QUESTION # 406
Refer to the Exhibit.
After the switch configuration the ping test fails between PC A and PC B Based on the output for switch 1.
which error must be corrected?
- A. Access mode is configured on the switch ports.
- B. There is a native VLAN mismatch
- C. The PCs are m the incorrect VLAN
- D. All VLANs are not enabled on the trunk
Answer: B
Explanation:
Explanation
From the output we see the native VLAN of Switch1 on Gi0/1 interface is VLAN 1 while that of Switch2 is VLAN 99 so there would be a native VLAN mismatch.
NEW QUESTION # 407
What is a function of Wireless LAN Controller?
- A. register with a single access point that controls traffic between wired and wireless endpoints.
- B. send LWAPP packets to access points.
- C. use SSIDs to distinguish between wireless clients.
- D. monitor activity on wireless and wired LANs
Answer: B
Explanation:
Lightweight APs (LAPs) is devices require no initial configuration. LAPs use the Lightweight Access Point Protocol (LWAPP) to communicate with a WLAN controller (WLC), as shown in the below figure.
Controller-based APs are useful in situations where many APs are required in the network.
As more APs are added, each AP is automatically configured and managed by the WLC.
NEW QUESTION # 408
Drag and drop the attack-mitigation techniques from the left onto the Types of attack that they mitigate on the right.
Answer:
Explanation:
NEW QUESTION # 409
Which output displays a JSON data representation?
- A. Option D
- B. Option B
- C. Option C
- D. Option A
Answer: A
NEW QUESTION # 410
Refer to the exhibit.
Which rule does the DHCP server use when there is an IP address conflict?
- A. The IP will be shown, even after the conflict is resolved.
- B. The address remains in the pool until the conflict is resolved.
- C. Only the IP detected by Gratuitous ARP is removed from the pool.
- D. The address is removed from the pool until the conflict is resolved.
- E. Only the IP detected by Ping is removed from the pool.
Answer: D
NEW QUESTION # 411
Refer to the exhibit.
What is the result if Gig1/11 receives an STP BPDU?
- A. The port transitions to the root port
- B. The port immediately transitions to STP forwarding.
- C. The port transitions to STP blocking
- D. The port goes into error-disable state
Answer: D
NEW QUESTION # 412
Which statement about Link Aggregation when implemented on a Cisco Wireless LAN Controller is true?
- A. When enabled the WLC bandwidth drops to 500 Mbps
- B. One functional physical port is needed to pass client traffic
- C. To pass client traffic two or more ports must be configured.
- D. The EtherChannel must be configured in "mode active"
Answer: A
NEW QUESTION # 413
Which protocol is the Cisco proprietary implementation of FHRP?
- A. GLBP
- B. HSRP
- C. VRRP
- D. CARP
Answer: B
NEW QUESTION # 414
What is the effect when loopback interfaces and the configured router ID are absent during the OSPF Process configuration?
- A. The lowest IP address is incremented by 1 and selected as the router ID.
- B. The highest up/up physical interface IP address is selected as the router ID.
- C. The router ID 0.0.0.0 is selected and placed in the OSPF process.
- D. No router ID is set, and the OSPF protocol does not run.
Answer: B
Explanation:
Section: IP Connectivity
NEW QUESTION # 415
Drag and drop the DNS commands from the left onto their effects on the right.
Answer:
Explanation:
NEW QUESTION # 416
Refer to the exhibit.
What are the two steps an engineer must take to provide the highest encryption and authentication using domain credentials from LDAP?
- A. Select PSK under Authentication Key Management
- B. Select 802.1X from under Authentication Key Management
- C. Select WPA+WPA2 on Layer 2 Security
- D. Select Static-WEP + 802.1X on Layer 2 Security
- E. Select WPA Policy with TKIP Encryption
Answer: B,C
NEW QUESTION # 417
Which two features can dynamically assign IPv6 addresses? (Choose two.)
- A. DHCP
- B. IPv6 stateful autoconfiguration
- C. IPv6 stateless autoconfiguration
- D. ISATAP tunneling
- E. NHRP
Answer: B,C
NEW QUESTION # 418
Drag and drop the functions of DHCP from the left onto any of the positions on the right Not all functions are used
Answer:
Explanation:
NEW QUESTION # 419
Refer to the exhibit.
What is the metric of the route to the 192.168.10.33/28 subnet?
- A. 0
- B. 1
- C. 2
- D. 3
- E. 4
Answer: C
NEW QUESTION # 420
......
Use Valid New 200-301 Test Notes & 200-301 Valid Exam Guide: https://www.examtorrent.com/200-301-valid-vce-dumps.html
200-301 Actual Questions Answers PDF 100% Cover Real Exam Questions: https://drive.google.com/open?id=1sQnrT_7DR3uux--cYqHBx75ysHRftcgn
