Last 200-301 practice test reviews: Practice Test Cisco dumps
Try 200-301 Free Now! Real Exam Question Answers Updated [Feb 13, 2024]
Cisco Certified Network Associate (CCNA) is a widely recognized certification program offered by Cisco Systems. The CCNA certification is designed to validate an individual’s skills and knowledge in the field of network engineering. The latest version of the CCNA certification is the Cisco 200-301 exam, which is a comprehensive and updated version of the previous CCNA exams. The new exam focuses on modern networking technologies and concepts, including security, automation, and programmability.
Cisco 200-301 is a certification exam for network professionals who want to validate their skills in implementing and managing Cisco networks. 200-301 exam is designed to test the candidate's knowledge and expertise in various network technologies, including network access, IP services, security fundamentals, automation, and programmability. Cisco Certified Network Associate Exam certification is intended for individuals who want to pursue a career in network engineering and administration.
Cisco 200-301 certification exam, also known as the Cisco Certified Network Associate (CCNA), is one of the most popular certification exams for IT professionals who want to build a career in networking. It is an entry-level certification that validates the knowledge and skills required to install, configure, operate, and troubleshoot medium-sized networks. 200-301 exam covers a wide range of topics, including network fundamentals, network access, IP connectivity, IP services, security fundamentals, and automation and programmability.
NEW QUESTION # 214
Refer to the Exhibit. After the switch configuration the ping test fails between PC A and PC B Based on the output for switch 1. Which error must be corrected?
- A. All VLANs are not enabled on the trunk
- B. There is a native VLAN mismatch
- C. The PCs are m the incorrect VLAN
- D. Access mode is configured on the switch ports.
Answer: B
Explanation:
From the output we see the native VLAN of Switch1 on Gi0/1 interface is VLAN 1 while that of Switch2 is VLAN 99 so there would be a native VLAN mismatch.
NEW QUESTION # 215
Refer to the exhibit.
Which configuration issue is preventing the OSPF neighbor relationship from being established between the two routers?
- A. R2 should have its network command in area 1
- B. R1 has an incorrect network command for interface Gi1/0
- C. R2 is using the passive-interface default command
- D. R1 interface Gil/0 has a larger MTU size
Answer: D
NEW QUESTION # 216
Refer to exhibit.
Which statement explains the configuration error message that is received?
- A. It is a broadcast IP address
- B. IT is a network IP address.
- C. The router does not support /28 mask.
- D. It belongs to a private IP address range.
Answer: A
NEW QUESTION # 217
Refer to the exhibit.
Drag and drop the networking parameters from the left onto the correct values on the right.
Answer:
Explanation:
Explanation
NIC vendor OUI -> 00:0C:22NIC MAC address -> 00:0C:22:83:79:A3default gateway -> 192.168.1.193host IP address -> 192.168.1.200subnet mask -> 255.255.255.192 The "ip route" and "ip addr show eth1" are Linux commands.+ "ip route": display the routing table+ "ip addr show eth1": get depth information (only on eth1 interface) about your network interfaces like IP Address, MAC Address information
NEW QUESTION # 218
Drag and drop the threat-mitigation techniques from the left onto the types of threat or attack they mitigate on the right.
Answer:
Explanation:
NEW QUESTION # 219
Refer to the exhibit.
Based on the LACP neighbor status, in which mode is the SW1 port channel configured?
- A. auto
- B. mode on
- C. active
- D. passive
Answer: D
NEW QUESTION # 220
Which command on a port enters the forwarding state immediately when a PC is connected to it?
- A. switch(config)#spanning-tree portfast default
- B. switch(config-if)#no spanning-tree portfast
- C. switch(config-if)#spanning-tree portfast trunk
- D. switch(config)#spanning-tree portfast bpduguard default
Answer: C
NEW QUESTION # 221
Refer to the exhibit.
How does router R1 handle traffic to 192.168.10.16?
- A. It selects the IS-IS route because it has the shortest prefix inclusive of the destination address.
- B. It selects the RIP route because it has the longest prefix inclusive of the destination address.
- C. It selects the EIGRP route because it has the lowest administrative distance.
- D. It selects the OSPF route because it has the lowest cost.
Answer: C
NEW QUESTION # 222 
Refer to the exhibit. An access-list is required to permit traffic from any host on interface GiO/O and deny traffic from interface GiO/i. Which access list must be applied?
- A. Option B
- B. Option C
- C. Option A
- D. Option D
Answer: C
NEW QUESTION # 223 
Refer to the exhibit. The show ip ospf interface command has been executed on R1. How is OSPF configured?
- A. The interface is not participating in OSPF.
- B. A point-to-point network type is configured.
- C. There are six OSPF neighbors on this interface.
- D. The default Hello and Dead timers are in use.
Answer: D
Explanation:
Section: IP Connectivity
Explanation:
From the output we can see there are Designated Router & Backup Designated Router for this OSPF domain so this is a broadcast network (point-to-point and point-to-multipoint networks do not elect DR & BDR).
By default, the timers on a broadcast network (Ethernet, point-to-point and point-to-multipoint) are 10 seconds hello and 40 seconds dead. The timers on a non-broadcast network are 30 seconds hello 120 seconds dead.
From the line "Neighbor Count is 3", we learn there are four OSPF routers in this OSPF domain.
Reference: https://www.cisco.com/c/en/us/support/docs/ip/open-shortest-path-first-ospf/13689-17.html
NEW QUESTION # 224
What is the primary effect of the spanning-tree port fast command?
- A. it enables BPDU messages
- B. It immediately enables the port in the listening state
- C. It minimizes spanning-tree convergence time
- D. It immediately puts the port into the forwarding state when the switch is reloaded
Answer: C
Explanation:
The purpose of Port Fast is to minimize the time interfaces must wait for spanning-tree to converge, it is effective only when used on interfaces connected to end stations.
https://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst3560/software/release/12-
2_55_se/configuration/guide/3560_scg/swstpopt.html
NEW QUESTION # 225
Refer to the exhibit.
An extended ACL has been configured configuration failed to work as
intended Which two
changes stop outbound traffic on TCP ports 25 and 80 to 10.0.20 0 26 from the 10.0.10 0/26 subnet while still allowing all other traffic? (Choose two )
- A. The ACL must be configured the Gi0/2 interface inbound on R1
- B. Add a "permit ip any any" statement at the end of ACL 101 for allowed traffic
- C. The ACL must be moved to the Gi0/1 interface outbound on R2
- D. Add a "permit ip any any" statement to the begining of ACL 101 for allowed traffic.
- E. The source and destination IPs must be swapped in ACL 101
Answer: B,E
NEW QUESTION # 226
Refer to the exhibit.
Which format matches the Modified EUI-64 IPv6 interface address for the network 2001:db8::/64?
- A. 2001 :db8:4425:5400:77ft:fe07:/64
- B. 2001 :db8::5200:00ff:fe04:0000/64
- C. 2001 :db8::5000:00ff:fe04 0000/64
- D. 2001 :db8::5000:0004:5678:0090/64
Answer: C
NEW QUESTION # 227
Refer to the exhibit.
An engineer booted a new switch and applied this configuration via the console port. Which additional configuration must be applied to allow administrators to authenticate directly to enable privilege mode via Telnet using a local username and password?
- A. Option B
- B. Option A
- C. Option C
- D. Option D
Answer: C
NEW QUESTION # 228
Refer to the exhibit.
Which prefix does Router 1 use for traffic to Host A?
- A. 10.10.13.0/25
- B. 10.10.13.208/29
- C. 10.10.10.0/28
- D. 10.10.13.144/28
Answer: B
Explanation:
Explanation
Host A address fall within the address range. However, if more than one route to the same subnet exist (router will use the longest stick match, which match more specific route to the subnet). If there are route
10.10.13.192/26 and 10.10.13.208/29, the router will forward the packet to /29 rather than /28.
NEW QUESTION # 229
Refer to the exhibit.
A router reserved these five routes from different routing information sources.
Which two routes does the router install in its routing table? (Choose two)
- A. iBGP route 10.0.0.0/30
- B. RIP route 10.0.0.0/30
- C. EIGRP route 10.0.0.1/32
- D. OSPF route 10.0.0.0/30
- E. OSPF route 10.0.0.0/16
Answer: C,D
NEW QUESTION # 230
Refer to the exhibit.
Which two commands were used to create port channel 10? (Choose two )
- A. Option B
- B. Option A
- C. Option E
- D. Option C
- E. Option D
Answer: B,D
NEW QUESTION # 231
Refer to the exhibit.
Users need to connect to the wireless network with IEEE 802. 11r-compatible devices. The connection must be maintained as users travel between floors or to other areas in the building What must be the configuration of the connection?
- A. Enable Fast Transition and select the FT 802.1x option.
- B. Enable Fast Transition and select the FT PSK option.
- C. Select the WPA Policy option with the CCKM option.
- D. Disable AES encryption.
Answer: A
NEW QUESTION # 232
Drag and drop the TCP or UDP details from the left onto their corresponding protocols on the right.
Answer:
Explanation:
NEW QUESTION # 233
Router R1 must send all traffic without a matching routing-table entry to 192.168.1.1. Which configuration accomplishes this task?
- A. Option B
- B. Option A
- C. Option C
- D. Option D
Answer: C
NEW QUESTION # 234
Refer to the exhibit. What is the next step to complete the implementation for the partial NAT configuration shown?
- A. Modify the access list for the internal network on e0/1.
- B. Reconfigure the static NAT entries that overlap the NAT pool.
- C. Configure the NAT outside interface.
- D. Apply the ACL to the pool configuration.
Answer: C
NEW QUESTION # 235
Refer to the exhibit.
Which route must be configured on R1 so that OSPF routing is used when OSPF is up. but the server is still reachable when OSPF goes down?
- A. ip route 10.1.1.0 255.255.255.0 172.16.2.2 100
- B. ip route 10.1.1.10 255.255.255.255 172.16.2.2 100
- C. ip route 10.1.1.10 255.255.255.255 gi0/0 125
- D. ip route 10.1.1.0 255.255.255.0 gi0/1 125
Answer: C
NEW QUESTION # 236
Refer to the exhibit.
If configuring a static default route on the router with the ip route 0.0.0.0 0.0.0.0 10.13.0.1 120 command how does the router respond?
- A. It starts sending traffic without a specific matching entry in the routing table to GigabitEthernetO/1
- B. It starts load-balancing traffic between the two default routes
- C. It immediately replaces the existing OSPF route in the routing table with the newly configured static route
- D. It ignores the new static route until the existing OSPF default route is removed
Answer: D
NEW QUESTION # 237
Refer to the exhibit. If configuring a static default route on the router with the ip route 0.0.0.0
0.0.0.0 10.13.0.1 120 command, how does the router respond?
- A. It starts load-balancing traffic between the two default routes
- B. It immediately replaces the existing OSPF route in the routing table with the newly configured static route
- C. It ignores the new static route until the existing OSPF default route is removed
- D. It starts sending traffic without a specific matching entry in the routing table to Gigabit EthernetO/1
Answer: C
Explanation:
Our new static default route has the Administrative Distance (AD) of 120, which is bigger than the AD of OSPF External route (O*E2) so it will not be pushed into the routing table until the current OSPF External route is removed.
For your information, if you don't type the AD of 120 (using the command "ip route 0.0.0.0 0.0.0.0
10.13.0.1") then the new static default route would replace the OSPF default route as the default AD of static route is 1. You will see such line in the routing table:
S* 0.0.0.0/0 [1/0] via 10.13.0.1
NEW QUESTION # 238
Refer to the exhibit.
which path is used by the router for internet traffic ?
- A. 10.10.10.0/28
- B. 209.165.200.0/27
- C. 10.10.13.0/24
- D. 0.0.0.0/0
Answer: D
NEW QUESTION # 239
......
Get Ready to Pass the 200-301 exam with Cisco Latest Practice Exam : https://www.examtorrent.com/200-301-valid-vce-dumps.html
Get Prepared for Your 200-301 Exam With Actual Cisco Study Guide!: https://drive.google.com/open?id=1cxAg6oib2tBSTZLYOvFUhG7oUOhxOp11
